There is a standard 10/100 Mbit/sec Ethernet jack on the back of the edgertronic high speed camera.
The camera has two Ethernet related LEDs.
Camera IP Address
The camera creates a file on the SD card that contains the camera's IP address.
After the camera LED is solid green, remove the SD card and check the file whose name starts with cam_pi_address and ends with the camera's IP address. For example, if you are using a DHCP server which assigned an address of 10.111.0.63 to your camera, then you should find the file cam_ip_address.10.111. 0.63 on the SD card.
You have two Ethernet network configuration choices.
- Internet networking - Connect your computer and the camera to your existing network infrastructure.
- Stand alone networking - Connect a network cable between your laptop and the camera.
Internet networking - camera connected to existing network
Your PC should already be connected to the existing network and you should be able to browse the Internet.
Your existing network will assign an IP address to the camera. The camera creates a file on the big SD card with the IP address in the filename. After the system LED blinks red/blue, remove the big SD card, insert it into your PC and you will be able to read the IP address of the camera.
Once you know the camera's IP address, stick the SD card back in the camera and type the IP address into your brower's address bar.
Stand alone networking - laptop to camera networking
If you are using the camera in a location where it is inconvenient to connect to an existing network, you can simply connect a network cable between your laptop and the camera. The camera will detect there is no network infrastructure and configure itself accordingly. You will need to modify your laptop network settings so the laptop can communicate with the camera.
Your laptop needs to be configured to use IP address 10.11.12.1. If you are familiar with laptop network configuration, you can make the changes now or click on one of the following links for step-by-step instruction:
- Windows 8 stand alone network configuration
- Windows 7 stand alone network configuration
- Mac stand alone network configuration
Once your laptop is configured, you can browse to the camera using the URL:
Changing the fixed IP address
For stand alone operations, the camera uses a default IP address:
Changing the fixed IP address is an experimental camera feature. If you make a mistake reset the camera to factory default values.
Software release 2.2 and newer
It is possible to change the camera's fixed IP address by saving a file named interfaces on the SD card and powering on the camera.
If you have two cameras, store the following contents into the interfaces file on the SD card on the second camera. It will have IP address 10.11.12.14.
auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.11.12.14 netmask 255.255.255.0 network 10.11.12.0 broadcast 10.11.12.255
If you have three cameras, store the following contents into the interfaces file on the SD card on the third camera. It will have IP address 10.11.12.15.
auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.11.12.15 netmask 255.255.255.0 network 10.11.12.0 broadcast 10.11.12.255
If you can no longer interact with the camera, reset the camera to factory default values.
Software release 1.7 and older
It is possible to change the camera's fixed IP address. Unfortunately, changing the fixed IP address can not be made via the web interface or by storing a configuration file on the SD card. You need to feel comfortable with command line tools like telnet and the text editor vi. You also need to understand IP networking concepts such as the network mask. The change is stored in non-volatile memory so you only have to make the change once.
The camera runs Linux and uses the standard /etc/network/interfaces file. The default contents of the interfaces file contains:
auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.11.12.13 netmask 255.255.255.0 network 10.11.12.0 broadcast 10.11.12.255
You adjust the eth0 settings to use a different fixed IP address. To make the change, you can telnet into the camera as user root (no password) and use the vi editor to modify the file.
On your computer, bring up a command or terminal window.
telnet 10.11.12.13 # or the DHCP IP address vi /etc/network/interfaces
Make your changes, double check everything is correct, and save your changes. Then you can activate your changes
ifconfig eth0 down ; ifconfig eth0 up
As soon as the camera takes down the eth0 interface, telnet will close. You should then be able to telnet back into the camera using the fixed IP address you configured. If you can no longer interact with the camera, reset the camera to factory default values.