Difference between revisions of "Genlock Adapter"

From edgertronic high speed video camera
Jump to: navigation, search
(Star or home run topology)
Line 1: Line 1:
The Genlock Accessory Box allows you to capture frame synchronized videos where the camera are separated by more than 25 feet.  In general, you need one Genlock Accessory Box per camera, unless you are routing the cabling through wiring closets, then you may need additional powered Genlock Accessory Boxs in each wiring closet.
+
The Genlock Accessory Box allows you to capture frame synchronized videos where the camera are separated by more than 25 feet.  In general, you need one Genlock Accessory Box per camera, unless you are routing the cabling through wiring closets, then you may need additional powered Genlock Accessory Boxes in each wiring closet.
  
  

Revision as of 12:01, 19 May 2020

The Genlock Accessory Box allows you to capture frame synchronized videos where the camera are separated by more than 25 feet. In general, you need one Genlock Accessory Box per camera, unless you are routing the cabling through wiring closets, then you may need additional powered Genlock Accessory Boxes in each wiring closet.


Genlock Adapter Specs

Dimensions (exclusive of cables) are 108.5mm x 104.5mm x 84.0mm

Genlock Adapter Ports

The Genlock Adapter has the following ports:

You must connect one, but not both of the following inputs:

  • IN - Genlock Input from an upstream Genlock Adapter. Connect using up to 1000' of Cat-5 or Cat-6 cable. This is NOT an Ethernet port. DO NOT connect to network hardware (POE Injectors, switches, routers etc.).
  • MASTER IN - Genlock Input from Master edgertronic camera. Set the intended Master camera to Genlock Master mode and connect using the supplied 2.5mm male to male cable. As a special case, when a Master edgertronic camera is connected to the MASTER IN port, you can also connect a wired or wireless trigger to the SLAVE_OUT / TRIGGER IN port.


One or more of the following Genlock outputs can be connected:

  • OUT1 - OUT4 - Genlock outputs to downstream Genlock Adapters. Connect using up to 1000' of Cat-5 or Cat-6 cable. This is NOT an Ethernet port. DO NOT connect to network hardware (POE Injectors, switches, routers etc.).
  • SLAVE OUT / TRIGGER IN - Genlock Output to Slave edgertronic camera. Set the intended Slave camera to Genlock Slave mode and connect using the supplied 2.5mm male to male cable. As a special case, when a Master edgertronic camera is connected to the MASTER IN port, you can also connect a wired or wireless trigger to the SLAVE_OUT / TRIGGER IN port.


The Genlock Adapter requires 5V @ 500mA

  • POWER - Connect one of the POWER ports to an edgertronic camera USB port, or an external USB charger, using the supplied USB male A to USB male A cable. You may use the second POWER port to daisy-chain power to a second Genlock Adapter box.

Wiring

Master Camera

  • Using a 2.5mm male/male cable, connect the IO port, on the back of the Master edgertronic camera, to the MASTER IN port on the front of the Genlock Adapter
  • Using a USB A to A cable, connect one of the USB ports, on the back of Master edgertronic camera, to one of the POWER ports on the front of the Genlock Adapter
  • Using CAT5 or CAT6 cable(s), connect one or more the the OUT1-OUT4 ports, on the back of the Genlock Adapter, to the IN port(s) on the front of one or more downstream Genlock Adapters.
  • Using the supplied power adapter or POE splitter, connect 12V to the power jack on the back of the Master edgertronic camera.
  • Connect ethernet to the back of the Master edgertronic camera.
  • Optionally, connect a wired or wireless trigger to the SLAVE_OUT / TRIGGER IN port, on the front of the Genlock Adapter, to trigger the Master and all downstream cameras.

The Genlock adapter is NOT an ethernet network device. To prevent severe damage, DO NOT connect the Genlock Adapter to any ethernet network port (switches, routers, POE, servers, computers etc).

Slave camera

  • Using a 2.5mm male/male cable, connect the IO port, on the back of the Slave edgertronic camera, to the SLAVE OUT/TRIGGER IN port on the front of the Genlock Adapter
  • Using a USB A to A cable, connect one of the USB ports, on the back of Slave edgertronic camera, to one of the POWER ports on the front of the Genlock Adapter
  • Using a CAT5 or CAT6 cable, connect the IN port, on the front of the Genlock Adapter, to one of the OUT1-OUT4 port(s) on the back of an upstream Genlock Adapter.
  • Optionally, using CAT5 or CAT6 cable(s), connect one or more the the OUT1-OUT4 ports, on the back of the Genlock Adapter, to the IN port(s) on the front of one or more downstream Genlock Adapters.
  • Using the supplied power adapter or POE splitter, connect 12V to the power jack on the back of the Slave edgertronic camera.
  • Connect ethernet to the back of the Slave edgertronic camera.

The Genlock adapter is NOT an ethernet network device. To prevent severe damage, DO NOT connect the Genlock Adapter to any ethernet network port (switches, routers, POE, servers, computers etc).

Expander

  • Using a USB A to A cable, connect a USB charger to one of the POWER ports on the front of the Genlock Adapter.
  • Optionally, using a USB A to A cable, daisy-chain power, to one(1) additional Genlock Adapter if using a 5V 1A charger, or three(3) additional Genlock Adapters if using a 5V 2A charger.
  • Using CAT5 or CAT6 cable, connect the IN port, on the front of the Genlock Adapter, to one of the OUT1-OUT4 port(s) on the back of an upstream Genlock Adapter.
  • Using CAT5 or CAT6 cable(s), connect one or more the the OUT1-OUT4 ports, on the back of the Genlock Adapter, to the IN port(s) on the front of one or more downstream Genlock Adapters.

The Genlock adapter is NOT an ethernet network device. To prevent severe damage, DO NOT connect the Genlock Adapter to any ethernet network port (switches, routers, POE, servers, computers etc).

Genlock Accessory Box connection examples

The Genlock Accessory Box supports several different wiring deployments.

The most important fact to keep in mind is not to confuse the cable – CAT5 – with the signaling protocol; ethernet signaling for camera control and genlock signaling for, well, genlock. CAT5 cabling was chosen because it is inexpensive, well designed, and ubiquitous. However, using CAT5 cabling for two incompatible purposes can easily lead to confusion. CAT6 is a higher quality cable, and can be used in place of CAT5.


Genlock cable extender

Genlock-adapter-extender.png

If you have two camera more than 25 feet apart, you can extend the distance by using two Genlock Adapters, as shown in the diagram.

If the camera are more then 1000 ft apart you can put additional genlock adapters at least every 1000ft. Power each genelock adapter, except the first and last, with a USB power supply.



Star or home run topology

If your cabling is going to follow typical small installation ethernet writing, there will be one writing closet that contains the network switch. This wiring topology is call star or alternately home run topology.

For example, if you have one master genlock camera and 3 slave cameras, the following equipment would be needed for star topology.

  • 4 cameras, one configured as master camera and 3 cameras configured as genlock slave.
  • 5 Genlock Accessory Boxs, one for each camera and one for the wiring closet. One USB power supply is needed for the Genlock Accessory Box in the closet.
  • 4 genlock CAT5 cables, going from the wiring closet to each camera.
  • 4 2.5mm cables that are included with the Genlock Accessory Box
  • 5 USB-A to USB-A cables that are included with the Genlock Accessory Box
  • USB charger

Daisy chain topology

One board per camera, each camera having 2 CAT5 cables, except for master and the last slave only needing one cable.

Many camera multi wiring cabinet

Checking your cabling design

After you design your cabling layout, verify all of the following assertions are true:

  • Each camera has one Genlock Accessory Box
  • Each camera has one CAT5 cable used for Ethernet that goes to an Ethernet switch
  • Each genlock slave camera has one CAT5 cable going from the camera's Genlock Accessory Box to another camera's Genlock Accessory Box
  • The genlock master camera has no more than four CAT 5 cables from genlock save camera's Genlock Accessory Boxs
  • Each Genlock Accessory Box that is not next to a camera has a USB power supply and a power source for the USB power supply